Technical guide

Salt air and your air-conditioner: what corrodes, and what helps

Fish Hoek sits close enough to the water that salt is not an occasional event. Onshore wind carries fine sea spray inland, it settles on metal surfaces, and overnight condensation turns that deposit into a mildly corrosive film. Refrigeration and air-conditioning equipment is especially exposed because it moves a lot of air across thin aluminium fins. This guide explains what actually happens to the equipment, without overstating it.

Fish Hoek · Cape Town

Why the outdoor coil fails first

An outdoor condenser works by pulling large volumes of air across closely spaced aluminium fins bonded to copper tubes. That design is excellent at heat transfer and poor at resisting deposits: salt lands on the fins, moisture holds it there, and the aluminium begins to pit. As the fins corrode they also lose the tight bond to the copper, so performance drops even before anything leaks.

The second casualty is usually the fixings and the casing: screws, brackets, fan guards and painted panels. A corroded bracket is a safety issue as much as a cosmetic one, particularly where a unit is wall-mounted above a walkway.

  • Aluminium fins: pitting, fin loss and reduced heat transfer
  • Copper pipework at brazed joints: surface corrosion and eventual pinholes
  • Fixings and brackets: weakened mounts and vibration
  • Electrical terminals: salt bridges causing intermittent faults
  • Fan blades and guards: imbalance, noise and cracked plastic

Placement is the cheapest protection

Two identical units, one under a roof overhang facing away from the prevailing wind and one on an exposed boundary wall, will age very differently. Before any coating or treatment is discussed, the position should be reviewed: can the unit be moved a metre, turned, or shielded without blocking airflow?

Shielding needs care. A solid enclosure that blocks wind also blocks airflow, and a unit that cannot reject heat will fail from overheating long before corrosion becomes the issue. Louvred screens with generous free area work better than solid boxes, and clearance in front of the coil should stay as the manufacturer specifies.

What maintenance actually does

Regular cleaning removes the salt deposit before it holds moisture against the metal. A soft rinse and a suitable coil cleaner, applied correctly, does more for equipment life than most aftermarket add-ons. What matters is frequency: a unit 200 metres from the sea needs attention more often than one in the valley behind the mountain.

Washing has limits and one real risk: high-pressure water bends fins flat. A gentle spray across the fins, not into them at close range, is the right approach, and electrical components should never be soaked.

  • Rinse the outdoor coil on a routine schedule, more often in exposed positions
  • Check and treat fixings and brackets before they weaken
  • Inspect electrical terminals for salt residue and discolouration
  • Keep the area around the unit clear of leaves, sand and stored items
  • Record what was found at each service so deterioration is visible over time

Coatings and treatments: what to expect

Factory-applied corrosion protection on coils and casings varies between manufacturers and is worth checking when specifying new equipment for an exposed site. Aftermarket coatings exist, and they can slow deterioration on a coil that is still in good condition, but they are a delay rather than a permanent answer, and a coating applied over existing corrosion traps the problem underneath.

Be sceptical of any product described as making equipment immune to coastal conditions. The honest position is that salt air shortens service life, and maintenance plus sensible placement lengthens it. There is no coating that removes the need to clean a coil.

When replacement beats repair

If the outdoor coil has lost a significant proportion of its fins, or the casing has corroded through at the mounting points, repair stops being economic. A new unit in a better position, with a coil that is clean from day one, will usually cost less over five years than repeatedly repairing a corroded one.

That decision should be made on evidence: fin condition, refrigerant pressures, compressor performance and the state of the mountings. We assess all four before recommending replacement.

Questions on this topic

It is a gradual effect rather than a line on a map. Properties within a few hundred metres of the shoreline, especially those exposed to onshore wind, see faster deterioration than homes further inland or sheltered by the ridge.

Related services in Fish Hoek

Next step

Tell us what is failing, and where.

Send the service, your suburb and a short description. We will come back with the next step and a quote before any work starts.

Call 084 690 1545 WhatsApp